1 /* $NetBSD: rtwreg.h,v 1.29 2016/09/15 21:45:37 jdolecek Exp $ */ 2 /*- 3 * Copyright (c) 2004, 2005 David Young. All rights reserved. 4 * 5 * Programmed for NetBSD by David Young. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 16 * THIS SOFTWARE IS PROVIDED BY David Young ``AS IS'' AND ANY 17 * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, 18 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 19 * PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL David 20 * Young BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, 21 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED 22 * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 23 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND 24 * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 25 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 26 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY 27 * OF SUCH DAMAGE. 28 */ 29 30 #include <lib/libkern/libkern.h> 31 32 /* RTL8180L Host Control and Status Registers */ 33 34 #define RTW_IDR0 0x00 /* ID Register: MAC addr, 6 bytes. 35 * Auto-loaded from EEPROM. Read by byte, 36 * by word, or by double word, but write 37 * only by double word. 38 */ 39 #define RTW_IDR1 0x04 40 41 #define RTW_MAR0 0x08 /* Multicast filter, 64b. */ 42 #define RTW_MAR1 0x0c 43 44 #define RTW_TSFTRL 0x18 /* Timing Synchronization Function Timer 45 * Register, low word, 32b, read-only. 46 */ 47 #define RTW_TSFTRH 0x1c /* High word, 32b, read-only. */ 48 #define RTW_TLPDA 0x20 /* Transmit Low Priority Descriptors Start 49 * Address, 32b, 256-byte alignment. 50 */ 51 #define RTW_TNPDA 0x24 /* Transmit Normal Priority Descriptors Start 52 * Address, 32b, 256-byte alignment. 53 */ 54 #define RTW_THPDA 0x28 /* Transmit High Priority Descriptors Start 55 * Address, 32b, 256-byte alignment. 56 */ 57 58 #define RTW_BRSR 0x2c /* Basic Rate Set Register, 16b */ 59 #define RTW_BRSR_BPLCP __BIT(8)/* 1: use short PLCP header for CTS/ACK packet, 60 * 0: use long PLCP header 61 */ 62 #define RTW_BRSR_MBR8180_MASK __BITS(1,0) /* Maximum Basic Service Rate */ 63 #define RTW_BRSR_MBR8180_1MBPS __SHIFTIN(0, RTW_BRSR_MBR8180_MASK) 64 #define RTW_BRSR_MBR8180_2MBPS __SHIFTIN(1, RTW_BRSR_MBR8180_MASK) 65 #define RTW_BRSR_MBR8180_5MBPS __SHIFTIN(2, RTW_BRSR_MBR8180_MASK) 66 #define RTW_BRSR_MBR8180_11MBPS __SHIFTIN(3, RTW_BRSR_MBR8180_MASK) 67 68 /* 8181 and 8180 docs conflict! */ 69 #define RTW_BRSR_MBR8181_1MBPS __BIT(0) 70 #define RTW_BRSR_MBR8181_2MBPS __BIT(1) 71 #define RTW_BRSR_MBR8181_5MBPS __BIT(2) 72 #define RTW_BRSR_MBR8181_11MBPS __BIT(3) 73 74 #define RTW_BSSID 0x2e 75 /* BSSID, 6 bytes */ 76 #define RTW_BSSID16 0x2e /* first two bytes */ 77 #define RTW_BSSID32 (0x2e + 4) /* remaining four bytes */ 78 #define RTW_BSSID0 RTW_BSSID16 /* BSSID[0], 8b */ 79 #define RTW_BSSID1 (RTW_BSSID0 + 1) /* BSSID[1], 8b */ 80 #define RTW_BSSID2 (RTW_BSSID1 + 1) /* BSSID[2], 8b */ 81 #define RTW_BSSID3 (RTW_BSSID2 + 1) /* BSSID[3], 8b */ 82 #define RTW_BSSID4 (RTW_BSSID3 + 1) /* BSSID[4], 8b */ 83 #define RTW_BSSID5 (RTW_BSSID4 + 1) /* BSSID[5], 8b */ 84 85 #define RTW_CR 0x37 /* Command Register, 8b */ 86 #define RTW_CR_RST __BIT(4)/* Reset: host sets to 1 to disable 87 * transmitter & receiver, reinitialize FIFO. 88 * RTL8180L sets to 0 to signal completion. 89 */ 90 #define RTW_CR_RE __BIT(3)/* Receiver Enable: host enables receiver 91 * by writing 1. RTL8180L indicates receiver 92 * is active with 1. After power-up, host 93 * must wait for reset before writing. 94 */ 95 #define RTW_CR_TE __BIT(2)/* Transmitter Enable: host enables transmitter 96 * by writing 1. RTL8180L indicates transmitter 97 * is active with 1. After power-up, host 98 * must wait for reset before writing. 99 */ 100 #define RTW_CR_MULRW __BIT(0)/* PCI Multiple Read/Write enable: 1 enables, 101 * 0 disables. XXX RTL8180, only? 102 */ 103 104 #define RTW_IMR 0x3c /* Interrupt Mask Register, 16b */ 105 #define RTW_ISR 0x3e /* Interrupt status register, 16b */ 106 107 #define RTW_INTR_TXFOVW __BIT(15) /* Tx FIFO underflow */ 108 #define RTW_INTR_TIMEOUT __BIT(14) /* Time Out: 1 indicates 109 * RTW_TSFTR[0:31] = RTW_TINT 110 */ 111 /* Beacon Time Out: time for host to prepare beacon: 112 * RTW_TSFTR % (RTW_BCNITV_BCNITV * TU) = 113 * (RTW_BCNITV_BCNITV * TU - RTW_BINTRITV) 114 */ 115 #define RTW_INTR_BCNINT __BIT(13) 116 /* ATIM Time Out: ATIM interval will pass, 117 * RTW_TSFTR % (RTW_BCNITV_BCNITV * TU) = 118 * (RTW_ATIMWND_ATIMWND * TU - RTW_ATIMTRITV) 119 */ 120 #define RTW_INTR_ATIMINT __BIT(12) 121 /* Tx Beacon Descriptor Error: beacon transmission aborted because frame Rx'd */ 122 #define RTW_INTR_TBDER __BIT(11) 123 #define RTW_INTR_TBDOK __BIT(10) /* Tx Beacon Descriptor OK */ 124 #define RTW_INTR_THPDER __BIT(9)/* Tx High Priority Descriptor Error: 125 * reached short/long retry limit 126 */ 127 #define RTW_INTR_THPDOK __BIT(8)/* Tx High Priority Descriptor OK */ 128 #define RTW_INTR_TNPDER __BIT(7)/* Tx Normal Priority Descriptor Error: 129 * reached short/long retry limit 130 */ 131 #define RTW_INTR_TNPDOK __BIT(6)/* Tx Normal Priority Descriptor OK */ 132 #define RTW_INTR_RXFOVW __BIT(5)/* Rx FIFO Overflow: either RDU (see below) 133 * or PCI bus too slow/busy 134 */ 135 #define RTW_INTR_RDU __BIT(4)/* Rx Descriptor Unavailable */ 136 #define RTW_INTR_TLPDER __BIT(3)/* Tx Normal Priority Descriptor Error 137 * reached short/long retry limit 138 */ 139 #define RTW_INTR_TLPDOK __BIT(2)/* Tx Normal Priority Descriptor OK */ 140 #define RTW_INTR_RER __BIT(1)/* Rx Error: CRC32 or ICV error */ 141 #define RTW_INTR_ROK __BIT(0)/* Rx OK */ 142 143 /* Convenient interrupt conjunctions. */ 144 #define RTW_INTR_RX (RTW_INTR_RER|RTW_INTR_ROK|RTW_INTR_RDU|RTW_INTR_RXFOVW) 145 #define RTW_INTR_TX (RTW_INTR_TLPDER|RTW_INTR_TLPDOK|RTW_INTR_THPDER|\ 146 RTW_INTR_THPDOK|RTW_INTR_TNPDER|RTW_INTR_TNPDOK|\ 147 RTW_INTR_TBDER|RTW_INTR_TBDOK) 148 #define RTW_INTR_BEACON (RTW_INTR_BCNINT|RTW_INTR_TBDER|RTW_INTR_TBDOK) 149 #define RTW_INTR_IOERROR (RTW_INTR_TXFOVW) 150 151 #define RTW_TCR 0x40 /* Transmit Configuration Register, 32b */ 152 #define RTW_TCR_CWMIN __BIT(31)/* 1: CWmin = 8, 0: CWmin = 32. */ 153 #define RTW_TCR_SWSEQ __BIT(30)/* 1: host assigns 802.11 sequence number, 154 * 0: hardware assigns sequence number 155 */ 156 /* Hardware version ID, read-only */ 157 #define RTW_TCR_HWVERID_MASK __BITS(29, 25) 158 #define RTW_TCR_HWVERID_D __SHIFTIN(26, RTW_TCR_HWVERID_MASK) 159 #define RTW_TCR_HWVERID_F __SHIFTIN(27, RTW_TCR_HWVERID_MASK) 160 #define RTW_TCR_HWVERID_RTL8180 RTW_TCR_HWVERID_F 161 162 /* Set ACK/CTS Timeout (EIFS). 163 * 1: ACK rate = max(RTW_BRSR_MBR, Rx rate) (XXX not min? typo in datasheet?) 164 * 0: ACK rate = 1Mbps 165 */ 166 #define RTW_TCR_SAT __BIT(24) 167 /* Max DMA Burst Size per Tx DMA Burst */ 168 #define RTW_TCR_MXDMA_MASK __BITS(23,21) 169 #define RTW_TCR_MXDMA_16 __SHIFTIN(0, RTW_TCR_MXDMA_MASK) 170 #define RTW_TCR_MXDMA_32 __SHIFTIN(1, RTW_TCR_MXDMA_MASK) 171 #define RTW_TCR_MXDMA_64 __SHIFTIN(2, RTW_TCR_MXDMA_MASK) 172 #define RTW_TCR_MXDMA_128 __SHIFTIN(3, RTW_TCR_MXDMA_MASK) 173 #define RTW_TCR_MXDMA_256 __SHIFTIN(4, RTW_TCR_MXDMA_MASK) 174 #define RTW_TCR_MXDMA_512 __SHIFTIN(5, RTW_TCR_MXDMA_MASK) 175 #define RTW_TCR_MXDMA_1024 __SHIFTIN(6, RTW_TCR_MXDMA_MASK) 176 #define RTW_TCR_MXDMA_2048 __SHIFTIN(7, RTW_TCR_MXDMA_MASK) 177 178 /* disable 802.11 random backoff */ 179 #define RTW_TCR_DISCW __BIT(20) 180 181 /* host lets RTL8180 append ICV to WEP packets */ 182 #define RTW_TCR_ICV __BIT(19) 183 184 /* Loopback Test: disables TXI/TXQ outputs. */ 185 #define RTW_TCR_LBK_MASK __BITS(18,17) 186 #define RTW_TCR_LBK_NORMAL __SHIFTIN(0, RTW_TCR_LBK_MASK) /* normal ops */ 187 #define RTW_TCR_LBK_MAC __SHIFTIN(1, RTW_TCR_LBK_MASK) /* MAC loopback */ 188 #define RTW_TCR_LBK_BBP __SHIFTIN(2, RTW_TCR_LBK_MASK) /* baseband loop. */ 189 #define RTW_TCR_LBK_CONT __SHIFTIN(3, RTW_TCR_LBK_MASK) /* continuous Tx */ 190 191 #define RTW_TCR_CRC __BIT(16) /* 0: RTL8180 appends CRC32 192 * 1: host appends CRC32 193 * 194 * (I *think* this is right. 195 * The docs have a mysterious 196 * description in the 197 * passive voice.) 198 */ 199 #define RTW_TCR_SRL_MASK __BITS(15,8) /* Short Retry Limit */ 200 #define RTW_TCR_LRL_MASK __BITS(7,0) /* Long Retry Limit */ 201 202 #define RTW_RCR 0x44 /* Receive Configuration Register, 32b */ 203 /* only do Early Rx on packets longer than 1536 bytes */ 204 #define RTW_RCR_ONLYERLPKT __BIT(31) 205 /* enable carrier sense method 2 */ 206 #define RTW_RCR_ENCS2 __BIT(30) 207 /* enable carrier sense method 1 */ 208 #define RTW_RCR_ENCS1 __BIT(29) 209 #define RTW_RCR_ENMARP __BIT(28) /* enable MAC auto-reset PHY */ 210 /* Check BSSID/ToDS/FromDS: set "Link On" when received BSSID 211 * matches RTW_BSSID and received ToDS/FromDS are appropriate 212 * according to RTW_MSR_NETYPE. 213 */ 214 #define RTW_RCR_CBSSID __BIT(23) 215 /* accept packets w/ PWRMGMT bit set */ 216 #define RTW_RCR_APWRMGT __BIT(22) 217 /* when RTW_MSR_NETYPE == RTW_MSR_NETYPE_INFRA_OK, accept 218 * broadcast/multicast packets whose 3rd address matches RTL8180's MAC. 219 */ 220 #define RTW_RCR_ADD3 __BIT(21) 221 #define RTW_RCR_AMF __BIT(20) /* accept management frames */ 222 #define RTW_RCR_ACF __BIT(19) /* accept control frames */ 223 #define RTW_RCR_ADF __BIT(18) /* accept data frames */ 224 /* Rx FIFO Threshold: RTL8180 begins PCI transfer when this many data 225 * bytes are received 226 */ 227 #define RTW_RCR_RXFTH_MASK __BITS(15,13) 228 #define RTW_RCR_RXFTH_64 __SHIFTIN(2, RTW_RCR_RXFTH_MASK) 229 #define RTW_RCR_RXFTH_128 __SHIFTIN(3, RTW_RCR_RXFTH_MASK) 230 #define RTW_RCR_RXFTH_256 __SHIFTIN(4, RTW_RCR_RXFTH_MASK) 231 #define RTW_RCR_RXFTH_512 __SHIFTIN(5, RTW_RCR_RXFTH_MASK) 232 #define RTW_RCR_RXFTH_1024 __SHIFTIN(6, RTW_RCR_RXFTH_MASK) 233 #define RTW_RCR_RXFTH_WHOLE __SHIFTIN(7, RTW_RCR_RXFTH_MASK) 234 235 #define RTW_RCR_AICV __BIT(12)/* accept frames w/ ICV errors */ 236 237 /* Max DMA Burst Size per Rx DMA Burst */ 238 #define RTW_RCR_MXDMA_MASK __BITS(10,8) 239 #define RTW_RCR_MXDMA_16 __SHIFTIN(0, RTW_RCR_MXDMA_MASK) 240 #define RTW_RCR_MXDMA_32 __SHIFTIN(1, RTW_RCR_MXDMA_MASK) 241 #define RTW_RCR_MXDMA_64 __SHIFTIN(2, RTW_RCR_MXDMA_MASK) 242 #define RTW_RCR_MXDMA_128 __SHIFTIN(3, RTW_RCR_MXDMA_MASK) 243 #define RTW_RCR_MXDMA_256 __SHIFTIN(4, RTW_RCR_MXDMA_MASK) 244 #define RTW_RCR_MXDMA_512 __SHIFTIN(5, RTW_RCR_MXDMA_MASK) 245 #define RTW_RCR_MXDMA_1024 __SHIFTIN(6, RTW_RCR_MXDMA_MASK) 246 #define RTW_RCR_MXDMA_UNLIMITED __SHIFTIN(7, RTW_RCR_MXDMA_MASK) 247 248 /* EEPROM type, read-only. 1: EEPROM is 93c56, 0: 93c46 */ 249 #define RTW_RCR_9356SEL __BIT(6) 250 251 #define RTW_RCR_ACRC32 __BIT(5)/* accept frames w/ CRC32 errors */ 252 #define RTW_RCR_AB __BIT(3)/* accept broadcast frames */ 253 #define RTW_RCR_AM __BIT(2)/* accept multicast frames */ 254 /* accept physical match frames. XXX means PLCP header ok? */ 255 #define RTW_RCR_APM __BIT(1) 256 #define RTW_RCR_AAP __BIT(0)/* accept frames w/ destination */ 257 258 /* Additional bits to set in monitor mode. */ 259 #define RTW_RCR_MONITOR ( \ 260 RTW_RCR_AAP | \ 261 RTW_RCR_ACF | \ 262 RTW_RCR_ACRC32 | \ 263 RTW_RCR_AICV | \ 264 0) 265 266 /* The packet filter bits. */ 267 #define RTW_RCR_PKTFILTER_MASK (\ 268 RTW_RCR_AAP | \ 269 RTW_RCR_AB | \ 270 RTW_RCR_ACF | \ 271 RTW_RCR_ACRC32 | \ 272 RTW_RCR_ADD3 | \ 273 RTW_RCR_ADF | \ 274 RTW_RCR_AICV | \ 275 RTW_RCR_AM | \ 276 RTW_RCR_AMF | \ 277 RTW_RCR_APM | \ 278 RTW_RCR_APWRMGT | \ 279 0) 280 281 /* Receive power-management frames and mgmt/ctrl/data frames. */ 282 #define RTW_RCR_PKTFILTER_DEFAULT ( \ 283 RTW_RCR_ACF | \ 284 RTW_RCR_ADF | \ 285 RTW_RCR_AMF | \ 286 RTW_RCR_APM | \ 287 RTW_RCR_APWRMGT | \ 288 0) 289 290 #define RTW_TINT 0x48 /* Timer Interrupt Register, 32b */ 291 #define RTW_TBDA 0x4c /* Transmit Beacon Descriptor Start Address, 292 * 32b, 256-byte alignment 293 */ 294 #define RTW_9346CR 0x50 /* 93c46/93c56 Command Register, 8b */ 295 #define RTW_9346CR_EEM_MASK __BITS(7,6) /* Operating Mode */ 296 #define RTW_9346CR_EEM_NORMAL __SHIFTIN(0, RTW_9346CR_EEM_MASK) 297 /* Load the EEPROM. Reset registers to defaults. 298 * Takes ~2ms. RTL8180 indicates completion with RTW_9346CR_EEM_NORMAL. 299 * XXX RTL8180 only? 300 */ 301 #define RTW_9346CR_EEM_AUTOLOAD __SHIFTIN(1, RTW_9346CR_EEM_MASK) 302 /* Disable network & bus-master operations and enable 303 * _EECS, _EESK, _EEDI, _EEDO. 304 * XXX RTL8180 only? 305 */ 306 #define RTW_9346CR_EEM_PROGRAM __SHIFTIN(2, RTW_9346CR_EEM_MASK) 307 /* Enable RTW_CONFIG[0123] registers. */ 308 #define RTW_9346CR_EEM_CONFIG __SHIFTIN(3, RTW_9346CR_EEM_MASK) 309 /* EEPROM pin status/control in _EEM_CONFIG, _EEM_AUTOLOAD modes. 310 * XXX RTL8180 only? 311 */ 312 #define RTW_9346CR_EECS __BIT(3) 313 #define RTW_9346CR_EESK __BIT(2) 314 #define RTW_9346CR_EEDI __BIT(1) 315 #define RTW_9346CR_EEDO __BIT(0) /* read-only */ 316 317 #define RTW_CONFIG0 0x51 /* Configuration Register 0, 8b */ 318 #define RTW_CONFIG0_WEP40 __BIT(7)/* implements 40-bit WEP, 319 * XXX RTL8180 only? 320 */ 321 #define RTW_CONFIG0_WEP104 __BIT(6)/* implements 104-bit WEP, 322 * from EEPROM, read-only 323 * XXX RTL8180 only? 324 */ 325 #define RTW_CONFIG0_LEDGPOEN __BIT(4)/* 1: RTW_PSR_LEDGPO[01] control 326 * LED[01] pins. 327 * 0: LED behavior defined by 328 * RTW_CONFIG1_LEDS10_MASK 329 * XXX RTL8180 only? 330 */ 331 /* auxiliary power is present, read-only */ 332 #define RTW_CONFIG0_AUXPWR __BIT(3) 333 /* Geographic Location, read-only */ 334 #define RTW_CONFIG0_GL_MASK __BITS(1,0) 335 /* _RTW_CONFIG0_GL_* is what the datasheet says, but RTW_CONFIG0_GL_* 336 * work. 337 */ 338 #define _RTW_CONFIG0_GL_USA __SHIFTIN(3, RTW_CONFIG0_GL_MASK) 339 #define RTW_CONFIG0_GL_EUROPE __SHIFTIN(2, RTW_CONFIG0_GL_MASK) 340 #define RTW_CONFIG0_GL_JAPAN __SHIFTIN(1, RTW_CONFIG0_GL_MASK) 341 #define RTW_CONFIG0_GL_USA __SHIFTIN(0, RTW_CONFIG0_GL_MASK) 342 /* RTL8181 datasheet says RTW_CONFIG0_GL_JAPAN = 0. */ 343 344 #define RTW_CONFIG1 0x52 /* Configuration Register 1, 8b */ 345 346 /* LED configuration. From EEPROM. Read/write. 347 * 348 * Setting LED0 LED1 349 * ------- ---- ---- 350 * RTW_CONFIG1_LEDS_ACT_INFRA Activity Infrastructure 351 * RTW_CONFIG1_LEDS_ACT_LINK Activity Link 352 * RTW_CONFIG1_LEDS_TX_RX Tx Rx 353 * RTW_CONFIG1_LEDS_LINKACT_INFRA Link/Activity Infrastructure 354 */ 355 #define RTW_CONFIG1_LEDS_MASK __BITS(7,6) 356 #define RTW_CONFIG1_LEDS_ACT_INFRA __SHIFTIN(0, RTW_CONFIG1_LEDS_MASK) 357 #define RTW_CONFIG1_LEDS_ACT_LINK __SHIFTIN(1, RTW_CONFIG1_LEDS_MASK) 358 #define RTW_CONFIG1_LEDS_TX_RX __SHIFTIN(2, RTW_CONFIG1_LEDS_MASK) 359 #define RTW_CONFIG1_LEDS_LINKACT_INFRA __SHIFTIN(3, RTW_CONFIG1_LEDS_MASK) 360 361 /* LWAKE Output Signal. Only applicable to Cardbus. Pulse width is 150ms. 362 * 363 * RTW_CONFIG1_LWACT 364 * 0 1 365 * RTW_CONFIG4_LWPTN 0 active high active low 366 * 1 positive pulse negative pulse 367 */ 368 #define RTW_CONFIG1_LWACT __BIT(4) 369 370 #define RTW_CONFIG1_MEMMAP __BIT(3)/* using PCI memory space, read-only */ 371 #define RTW_CONFIG1_IOMAP __BIT(2)/* using PCI I/O space, read-only */ 372 #define RTW_CONFIG1_VPD __BIT(1)/* if set, VPD from offsets 373 * 0x40-0x7f in EEPROM are at 374 * registers 0x60-0x67 of PCI 375 * Configuration Space (XXX huh?) 376 */ 377 #define RTW_CONFIG1_PMEN __BIT(0)/* Power Management Enable: TBD */ 378 379 #define RTW_CONFIG2 0x53 /* Configuration Register 2, 8b */ 380 #define RTW_CONFIG2_LCK __BIT(7)/* clocks are locked, read-only: 381 * Tx frequency & symbol clocks 382 * are derived from the same OSC 383 */ 384 #define RTW_CONFIG2_ANT __BIT(6) /* diversity enabled, read-only */ 385 #define RTW_CONFIG2_DPS __BIT(3) /* Descriptor Polling State: enable 386 * test mode. 387 */ 388 #define RTW_CONFIG2_PAPESIGN __BIT(2) /* TBD, from EEPROM */ 389 #define RTW_CONFIG2_PAPETIME_MASK __BITS(1,0) /* TBD, from EEPROM */ 390 391 #define RTW_ANAPARM 0x54 /* Analog parameter, 32b */ 392 #define RTW_ANAPARM_RFPOW0_MASK __BITS(30,28) /* undocumented bits 393 * which appear to 394 * control the power 395 * state of the RF 396 * components 397 */ 398 #define RTW_ANAPARM_RFPOW_MASK \ 399 (RTW_ANAPARM_RFPOW0_MASK|RTW_ANAPARM_RFPOW1_MASK) 400 401 #define RTW_ANAPARM_TXDACOFF __BIT(27) /* 1: disable Tx DAC, 402 * 0: enable 403 */ 404 #define RTW_ANAPARM_RFPOW1_MASK __BITS(26,20) /* undocumented bits 405 * which appear to 406 * control the power 407 * state of the RF 408 * components 409 */ 410 411 /* 412 * Maxim On/Sleep/Off control 413 */ 414 #define RTW_ANAPARM_RFPOW_MAXIM_ON __SHIFTIN(0x8, RTW_ANAPARM_RFPOW1_MASK) 415 416 /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ 417 #define RTW_ANAPARM_RFPOW_MAXIM_SLEEP __SHIFTIN(0x378, RTW_ANAPARM_RFPOW1_MASK) 418 419 /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ 420 #define RTW_ANAPARM_RFPOW_MAXIM_OFF __SHIFTIN(0x379, RTW_ANAPARM_RFPOW1_MASK) 421 422 /* 423 * RFMD On/Sleep/Off control 424 */ 425 #define RTW_ANAPARM_RFPOW_RFMD_ON __SHIFTIN(0x408, RTW_ANAPARM_RFPOW1_MASK) 426 427 /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ 428 #define RTW_ANAPARM_RFPOW_RFMD_SLEEP __SHIFTIN(0x378, RTW_ANAPARM_RFPOW1_MASK) 429 430 /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ 431 #define RTW_ANAPARM_RFPOW_RFMD_OFF __SHIFTIN(0x379, RTW_ANAPARM_RFPOW1_MASK) 432 433 /* 434 * Philips On/Sleep/Off control 435 */ 436 #define RTW_ANAPARM_RFPOW_ANA_PHILIPS_ON \ 437 __SHIFTIN(0x328, RTW_ANAPARM_RFPOW1_MASK) 438 #define RTW_ANAPARM_RFPOW_DIG_PHILIPS_ON \ 439 __SHIFTIN(0x008, RTW_ANAPARM_RFPOW1_MASK) 440 441 /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ 442 #define RTW_ANAPARM_RFPOW_PHILIPS_SLEEP\ 443 __SHIFTIN(0x378, RTW_ANAPARM_RFPOW1_MASK) 444 445 /* reg[RTW_ANAPARM] |= RTW_ANAPARM_TXDACOFF; */ 446 #define RTW_ANAPARM_RFPOW_PHILIPS_OFF\ 447 __SHIFTIN(0x379, RTW_ANAPARM_RFPOW1_MASK) 448 449 #define RTW_ANAPARM_RFPOW_PHILIPS_ON __SHIFTIN(0x328, RTW_ANAPARM_RFPOW1_MASK) 450 451 #define RTW_ANAPARM_CARDSP_MASK __BITS(19,0) /* undocumented 452 * card-specific 453 * bits from the 454 * EEPROM. 455 */ 456 457 #define RTW_MSR 0x58 /* Media Status Register, 8b */ 458 /* Network Type and Link Status */ 459 #define RTW_MSR_NETYPE_MASK __BITS(3,2) 460 /* AP, XXX RTL8181 only? */ 461 #define RTW_MSR_NETYPE_AP_OK __SHIFTIN(3, RTW_MSR_NETYPE_MASK) 462 /* infrastructure link ok */ 463 #define RTW_MSR_NETYPE_INFRA_OK __SHIFTIN(2, RTW_MSR_NETYPE_MASK) 464 /* ad-hoc link ok */ 465 #define RTW_MSR_NETYPE_ADHOC_OK __SHIFTIN(1, RTW_MSR_NETYPE_MASK) 466 /* no link */ 467 #define RTW_MSR_NETYPE_NOLINK __SHIFTIN(0, RTW_MSR_NETYPE_MASK) 468 469 #define RTW_CONFIG3 0x59 /* Configuration Register 3, 8b */ 470 #define RTW_CONFIG3_GNTSEL __BIT(7) /* Grant Select, read-only */ 471 #define RTW_CONFIG3_PARMEN __BIT(6) /* Set RTW_CONFIG3_PARMEN and 472 * RTW_9346CR_EEM_CONFIG to 473 * allow RTW_ANAPARM writes. 474 */ 475 #define RTW_CONFIG3_MAGIC __BIT(5)/* Valid when RTW_CONFIG1_PMEN is 476 * set. If set, RTL8180 wakes up 477 * OS when Magic Packet is Rx'd. 478 */ 479 #define RTW_CONFIG3_CARDBEN __BIT(3)/* Cardbus-related registers 480 * and functions are enabled, 481 * read-only. XXX RTL8180 only. 482 */ 483 #define RTW_CONFIG3_CLKRUNEN __BIT(2)/* CLKRUN enabled, read-only. 484 * XXX RTL8180 only. 485 */ 486 #define RTW_CONFIG3_FUNCREGEN __BIT(1)/* Function Registers Enabled, 487 * read-only. XXX RTL8180 only. 488 */ 489 #define RTW_CONFIG3_FBTBEN __BIT(0)/* Fast back-to-back enabled, 490 * read-only. 491 */ 492 #define RTW_CONFIG4 0x5A /* Configuration Register 4, 8b */ 493 #define RTW_CONFIG4_VCOPDN __BIT(7)/* VCO Power Down 494 * 0: normal operation 495 * (power-on default) 496 * 1: power-down VCO, RF front-end, 497 * and most RTL8180 components. 498 */ 499 #define RTW_CONFIG4_PWROFF __BIT(6)/* Power Off 500 * 0: normal operation 501 * (power-on default) 502 * 1: power-down RF front-end, 503 * and most RTL8180 components, 504 * but leave VCO on. 505 * 506 * XXX RFMD front-end only? 507 */ 508 #define RTW_CONFIG4_PWRMGT __BIT(5)/* Power Management 509 * 0: normal operation 510 * (power-on default) 511 * 1: set Tx packet's PWRMGMT bit. 512 */ 513 #define RTW_CONFIG4_LWPME __BIT(4)/* LANWAKE vs. PMEB: Cardbus-only 514 * 0: LWAKE & PMEB asserted 515 * simultaneously 516 * 1: LWAKE asserted only if 517 * both PMEB is asserted and 518 * ISOLATEB is low. 519 * XXX RTL8180 only. 520 */ 521 #define RTW_CONFIG4_LWPTN __BIT(2)/* see RTW_CONFIG1_LWACT 522 * XXX RTL8180 only. 523 */ 524 /* Radio Front-End Programming Method */ 525 #define RTW_CONFIG4_RFTYPE_MASK __BITS(1,0) 526 #define RTW_CONFIG4_RFTYPE_INTERSIL __SHIFTIN(1, RTW_CONFIG4_RFTYPE_MASK) 527 #define RTW_CONFIG4_RFTYPE_RFMD __SHIFTIN(2, RTW_CONFIG4_RFTYPE_MASK) 528 #define RTW_CONFIG4_RFTYPE_PHILIPS __SHIFTIN(3, RTW_CONFIG4_RFTYPE_MASK) 529 530 #define RTW_TESTR 0x5B /* TEST mode register, 8b */ 531 532 #define RTW_PSR 0x5e /* Page Select Register, 8b */ 533 #define RTW_PSR_GPO __BIT(7)/* Control/status of pin 52. */ 534 #define RTW_PSR_GPI __BIT(6)/* Status of pin 64. */ 535 #define RTW_PSR_LEDGPO1 __BIT(5)/* Status/control of LED1 pin if 536 * RTW_CONFIG0_LEDGPOEN is set. 537 */ 538 #define RTW_PSR_LEDGPO0 __BIT(4)/* Status/control of LED0 pin if 539 * RTW_CONFIG0_LEDGPOEN is set. 540 */ 541 #define RTW_PSR_UWF __BIT(1)/* Enable Unicast Wakeup Frame */ 542 #define RTW_PSR_PSEN __BIT(0)/* 1: page 1, 0: page 0 */ 543 544 #define RTW_SCR 0x5f /* Security Configuration Register, 8b */ 545 #define RTW_SCR_KM_MASK __BITS(5,4) /* Key Mode */ 546 #define RTW_SCR_KM_WEP104 __SHIFTIN(1, RTW_SCR_KM_MASK) 547 #define RTW_SCR_KM_WEP40 __SHIFTIN(0, RTW_SCR_KM_MASK) 548 #define RTW_SCR_TXSECON __BIT(1)/* Enable Tx WEP. Invalid if 549 * neither RTW_CONFIG0_WEP40 nor 550 * RTW_CONFIG0_WEP104 is set. 551 */ 552 #define RTW_SCR_RXSECON __BIT(0)/* Enable Rx WEP. Invalid if 553 * neither RTW_CONFIG0_WEP40 nor 554 * RTW_CONFIG0_WEP104 is set. 555 */ 556 557 #define RTW_BCNITV 0x70 /* Beacon Interval Register, 16b */ 558 #define RTW_BCNITV_BCNITV_MASK __BITS(9,0) /* TU between TBTT, written 559 * by host. 560 */ 561 #define RTW_ATIMWND 0x72 /* ATIM Window Register, 16b */ 562 #define RTW_ATIMWND_ATIMWND __BITS(9,0) /* ATIM Window length in TU, 563 * written by host. 564 */ 565 566 #define RTW_BINTRITV 0x74 /* Beacon Interrupt Interval Register, 16b */ 567 #define RTW_BINTRITV_BINTRITV __BITS(9,0) /* RTL8180 wakes host with 568 * RTW_INTR_BCNINT at BINTRITV 569 * microseconds before TBTT 570 */ 571 #define RTW_ATIMTRITV 0x76 /* ATIM Interrupt Interval Register, 16b */ 572 #define RTW_ATIMTRITV_ATIMTRITV __BITS(9,0) /* RTL8180 wakes host with 573 * RTW_INTR_ATIMINT at ATIMTRITV 574 * microseconds before end of 575 * ATIM Window 576 */ 577 578 #define RTW_PHYDELAY 0x78 /* PHY Delay Register, 8b */ 579 #define RTW_PHYDELAY_REVC_MAGIC __BIT(3) /* Rev. C magic from reference 580 * driver 581 */ 582 #define RTW_PHYDELAY_PHYDELAY __BITS(2,0) /* microsecond Tx delay between 583 * MAC and RF front-end 584 */ 585 #define RTW_CRCOUNT 0x79 /* Carrier Sense Counter, 8b */ 586 #define RTW_CRCOUNT_MAGIC 0x4c 587 588 #define RTW_CRC16ERR 0x7a /* CRC16 error count, 16b, XXX RTL8181 only? */ 589 590 #define RTW_BB 0x7c /* Baseband interface, 32b */ 591 /* used for writing RTL8180's integrated baseband processor */ 592 #define RTW_BB_RD_MASK __BITS(23,16) /* data to read */ 593 #define RTW_BB_WR_MASK __BITS(15,8) /* data to write */ 594 #define RTW_BB_WREN __BIT(7) /* write enable */ 595 #define RTW_BB_ADDR_MASK __BITS(6,0) /* address */ 596 597 #define RTW_PHYADDR 0x7c /* Address register for PHY interface, 8b */ 598 #define RTW_PHYDATAW 0x7d /* Write data to PHY, 8b, write-only */ 599 #define RTW_PHYDATAR 0x7e /* Read data from PHY, 8b (?), read-only */ 600 601 #define RTW_PHYCFG 0x80 /* PHY Configuration Register, 32b */ 602 #define RTW_PHYCFG_MAC_POLL __BIT(31) /* if !RTW_PHYCFG_HST, 603 * host sets. MAC clears 604 * after banging bits. 605 */ 606 #define RTW_PHYCFG_HST __BIT(30) /* 1: host bangs bits 607 * 0: MAC bangs bits 608 */ 609 #define RTW_PHYCFG_MAC_RFTYPE_MASK __BITS(29,28) 610 #define RTW_PHYCFG_MAC_RFTYPE_INTERSIL __SHIFTIN(0, RTW_PHYCFG_MAC_RFTYPE_MASK) 611 #define RTW_PHYCFG_MAC_RFTYPE_RFMD __SHIFTIN(1, RTW_PHYCFG_MAC_RFTYPE_MASK) 612 #define RTW_PHYCFG_MAC_RFTYPE_GCT RTW_PHYCFG_MAC_RFTYPE_RFMD 613 #define RTW_PHYCFG_MAC_RFTYPE_PHILIPS __SHIFTIN(3, RTW_PHYCFG_MAC_RFTYPE_MASK) 614 #define RTW_PHYCFG_MAC_PHILIPS_ADDR_MASK __BITS(27,24) 615 #define RTW_PHYCFG_MAC_PHILIPS_DATA_MASK __BITS(23,0) 616 #define RTW_PHYCFG_MAC_MAXIM_LODATA_MASK __BITS(27,24) 617 #define RTW_PHYCFG_MAC_MAXIM_ADDR_MASK __BITS(11,8) 618 #define RTW_PHYCFG_MAC_MAXIM_HIDATA_MASK __BITS(7,0) 619 #define RTW_PHYCFG_HST_EN __BIT(2) 620 #define RTW_PHYCFG_HST_CLK __BIT(1) 621 #define RTW_PHYCFG_HST_DATA __BIT(0) 622 623 #define RTW_MAXIM_HIDATA_MASK __BITS(11,4) 624 #define RTW_MAXIM_LODATA_MASK __BITS(3,0) 625 626 /** 627 ** 0x84 - 0xD3, page 1, selected when RTW_PSR[PSEN] == 1. 628 **/ 629 630 #define RTW_WAKEUP0L 0x84 /* Power Management Wakeup Frame */ 631 #define RTW_WAKEUP0H 0x88 /* 32b */ 632 633 #define RTW_WAKEUP1L 0x8c 634 #define RTW_WAKEUP1H 0x90 635 636 #define RTW_WAKEUP2LL 0x94 637 #define RTW_WAKEUP2LH 0x98 638 639 #define RTW_WAKEUP2HL 0x9c 640 #define RTW_WAKEUP2HH 0xa0 641 642 #define RTW_WAKEUP3LL 0xa4 643 #define RTW_WAKEUP3LH 0xa8 644 645 #define RTW_WAKEUP3HL 0xac 646 #define RTW_WAKEUP3HH 0xb0 647 648 #define RTW_WAKEUP4LL 0xb4 649 #define RTW_WAKEUP4LH 0xb8 650 651 #define RTW_WAKEUP4HL 0xbc 652 #define RTW_WAKEUP4HH 0xc0 653 654 #define RTW_CRC0 0xc4 /* CRC of wakeup frame 0, 16b */ 655 #define RTW_CRC1 0xc6 /* CRC of wakeup frame 1, 16b */ 656 #define RTW_CRC2 0xc8 /* CRC of wakeup frame 2, 16b */ 657 #define RTW_CRC3 0xca /* CRC of wakeup frame 3, 16b */ 658 #define RTW_CRC4 0xcc /* CRC of wakeup frame 4, 16b */ 659 660 /** 661 ** 0x84 - 0xD3, page 0, selected when RTW_PSR[PSEN] == 0. 662 **/ 663 664 /* Default Key Registers, each 128b 665 * 666 * If RTW_SCR_KM_WEP104, 104 lsb are the key. 667 * If RTW_SCR_KM_WEP40, 40 lsb are the key. 668 */ 669 #define RTW_DK0 0x90 /* Default Key 0 Register, 128b */ 670 #define RTW_DK1 0xa0 /* Default Key 1 Register, 128b */ 671 #define RTW_DK2 0xb0 /* Default Key 2 Register, 128b */ 672 #define RTW_DK3 0xc0 /* Default Key 3 Register, 128b */ 673 674 #define RTW_CONFIG5 0xd8 /* Configuration Register 5, 8b */ 675 #define RTW_CONFIG5_TXFIFOOK __BIT(7)/* Tx FIFO self-test pass, read-only */ 676 #define RTW_CONFIG5_RXFIFOOK __BIT(6)/* Rx FIFO self-test pass, read-only */ 677 #define RTW_CONFIG5_CALON __BIT(5)/* 1: start calibration cycle 678 * and raise AGCRESET pin. 679 * 0: lower AGCRESET pin 680 */ 681 #define RTW_CONFIG5_EACPI __BIT(2)/* Enable ACPI Wake up, default 0 */ 682 #define RTW_CONFIG5_LANWAKE __BIT(1)/* Enable LAN Wake signal, 683 * from EEPROM 684 */ 685 #define RTW_CONFIG5_PMESTS __BIT(0)/* 1: both software & PCI Reset 686 * reset PME_Status 687 * 0: only software resets PME_Status 688 * 689 * From EEPROM. 690 */ 691 692 #define RTW_TPPOLL 0xd9 /* Transmit Priority Polling Register, 8b, 693 * write-only. 694 */ 695 #define RTW_TPPOLL_BQ __BIT(7)/* RTL8180 clears to notify host of a beacon 696 * Tx. Host writes have no effect. 697 */ 698 #define RTW_TPPOLL_HPQ __BIT(6)/* Host writes 1 to notify RTL8180 of 699 * high-priority Tx packets, RTL8180 clears 700 * to after high-priority Tx is complete. 701 */ 702 #define RTW_TPPOLL_NPQ __BIT(5)/* If RTW_CONFIG2_DPS is set, 703 * host writes 1 to notify RTL8180 of 704 * normal-priority Tx packets, RTL8180 clears 705 * after normal-priority Tx is complete. 706 * 707 * If RTW_CONFIG2_DPS is clear, host writes 708 * have no effect. RTL8180 clears after 709 * normal-priority Tx is complete. 710 */ 711 #define RTW_TPPOLL_LPQ __BIT(4)/* Host writes 1 to notify RTL8180 of 712 * low-priority Tx packets, RTL8180 clears 713 * after low-priority Tx is complete. 714 */ 715 #define RTW_TPPOLL_SBQ __BIT(3)/* Host writes 1 to tell RTL8180 to 716 * stop beacon DMA. This bit is invalid 717 * when RTW_CONFIG2_DPS is set. 718 */ 719 #define RTW_TPPOLL_SHPQ __BIT(2)/* Host writes 1 to tell RTL8180 to 720 * stop high-priority DMA. 721 */ 722 #define RTW_TPPOLL_SNPQ __BIT(1)/* Host writes 1 to tell RTL8180 to 723 * stop normal-priority DMA. This bit is invalid 724 * when RTW_CONFIG2_DPS is set. 725 */ 726 #define RTW_TPPOLL_SLPQ __BIT(0)/* Host writes 1 to tell RTL8180 to 727 * stop low-priority DMA. 728 */ 729 730 /* Start all queues. */ 731 #define RTW_TPPOLL_ALL (RTW_TPPOLL_BQ | RTW_TPPOLL_HPQ | \ 732 RTW_TPPOLL_NPQ | RTW_TPPOLL_LPQ) 733 /* Check all queues' activity. */ 734 #define RTW_TPPOLL_ACTIVE RTW_TPPOLL_ALL 735 /* Stop all queues. */ 736 #define RTW_TPPOLL_SALL (RTW_TPPOLL_SBQ | RTW_TPPOLL_SHPQ | \ 737 RTW_TPPOLL_SNPQ | RTW_TPPOLL_SLPQ) 738 739 #define RTW_CWR 0xdc /* Contention Window Register, 16b, read-only */ 740 /* Contention Window: indicates number of contention windows before Tx 741 */ 742 #define RTW_CWR_CW __BITS(9,0) 743 744 /* Retry Count Register, 16b, read-only */ 745 #define RTW_RETRYCTR 0xde 746 /* Retry Count: indicates number of retries after Tx */ 747 #define RTW_RETRYCTR_RETRYCT __BITS(7,0) 748 749 #define RTW_RDSAR 0xe4 /* Receive descriptor Start Address Register, 750 * 32b, 256-byte alignment. 751 */ 752 /* Function Event Register, 32b, Cardbus only. Only valid when 753 * both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN are set. 754 */ 755 #define RTW_FER 0xf0 756 #define RTW_FER_INTR __BIT(15) /* set when RTW_FFER_INTR is set */ 757 #define RTW_FER_GWAKE __BIT(4) /* General Wakeup */ 758 /* Function Event Mask Register, 32b, Cardbus only. Only valid when 759 * both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN are set. 760 */ 761 #define RTW_FEMR 0xf4 762 #define RTW_FEMR_INTR __BIT(15) /* set when RTW_FFER_INTR is set */ 763 #define RTW_FEMR_WKUP __BIT(14) /* Wakeup Mask */ 764 #define RTW_FEMR_GWAKE __BIT(4) /* General Wakeup */ 765 /* Function Present State Register, 32b, read-only, Cardbus only. 766 * Only valid when both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN 767 * are set. 768 */ 769 #define RTW_FPSR 0xf8 770 #define RTW_FPSR_INTR __BIT(15) /* TBD */ 771 #define RTW_FPSR_GWAKE __BIT(4) /* General Wakeup: TBD */ 772 /* Function Force Event Register, 32b, write-only, Cardbus only. 773 * Only valid when both RTW_CONFIG3_CARDBEN and RTW_CONFIG3_FUNCREGEN 774 * are set. 775 */ 776 #define RTW_FFER 0xfc 777 #define RTW_FFER_INTR __BIT(15) /* TBD */ 778 #define RTW_FFER_GWAKE __BIT(4) /* General Wakeup: TBD */ 779 780 /* Serial EEPROM offsets */ 781 #define RTW_SR_ID 0x00 /* 16b */ 782 #define RTW_SR_VID 0x02 /* 16b */ 783 #define RTW_SR_DID 0x04 /* 16b */ 784 #define RTW_SR_SVID 0x06 /* 16b */ 785 #define RTW_SR_SMID 0x08 /* 16b */ 786 #define RTW_SR_MNGNT 0x0a 787 #define RTW_SR_MXLAT 0x0b 788 #define RTW_SR_RFCHIPID 0x0c 789 #define RTW_SR_CONFIG3 0x0d 790 #define RTW_SR_MAC 0x0e /* 6 bytes */ 791 #define RTW_SR_CONFIG0 0x14 792 #define RTW_SR_CONFIG1 0x15 793 #define RTW_SR_PMC 0x16 /* Power Management Capabilities, 16b */ 794 #define RTW_SR_CONFIG2 0x18 795 #define RTW_SR_CONFIG4 0x19 796 #define RTW_SR_ANAPARM 0x1a /* Analog Parameters, 32b */ 797 #define RTW_SR_TESTR 0x1e 798 #define RTW_SR_CONFIG5 0x1f 799 #define RTW_SR_TXPOWER1 0x20 800 #define RTW_SR_TXPOWER2 0x21 801 #define RTW_SR_TXPOWER3 0x22 802 #define RTW_SR_TXPOWER4 0x23 803 #define RTW_SR_TXPOWER5 0x24 804 #define RTW_SR_TXPOWER6 0x25 805 #define RTW_SR_TXPOWER7 0x26 806 #define RTW_SR_TXPOWER8 0x27 807 #define RTW_SR_TXPOWER9 0x28 808 #define RTW_SR_TXPOWER10 0x29 809 #define RTW_SR_TXPOWER11 0x2a 810 #define RTW_SR_TXPOWER12 0x2b 811 #define RTW_SR_TXPOWER13 0x2c 812 #define RTW_SR_TXPOWER14 0x2d 813 #define RTW_SR_CHANNELPLAN 0x2e /* bitmap of channels to scan */ 814 #define RTW_SR_ENERGYDETTHR 0x2f /* energy-detect threshold */ 815 #define RTW_SR_ENERGYDETTHR_DEFAULT 0x0c /* use this if old SROM */ 816 #define RTW_SR_CISPOINTER 0x30 /* 16b */ 817 #define RTW_SR_RFPARM 0x32 /* RF-specific parameter */ 818 #define RTW_SR_RFPARM_DIGPHY __BIT(0) /* 1: digital PHY */ 819 #define RTW_SR_RFPARM_DFLANTB __BIT(1) /* 1: antenna B is default */ 820 #define RTW_SR_RFPARM_CS_MASK __BITS(2,3) /* carrier-sense type */ 821 #define RTW_SR_VERSION 0x3c /* EEPROM content version, 16b */ 822 #define RTW_SR_CRC 0x3e /* EEPROM content CRC, 16b */ 823 #define RTW_SR_VPD 0x40 /* Vital Product Data, 64 bytes */ 824 #define RTW_SR_CIS 0x80 /* CIS Data, 93c56 only, 128 bytes*/ 825 826 /* 827 * RTL8180 Transmit/Receive Descriptors 828 */ 829 830 /* the first descriptor in each ring must be on a 256-byte boundary */ 831 #define RTW_DESC_ALIGNMENT 256 832 833 /* Tx descriptor */ 834 struct rtw_txdesc { 835 volatile uint32_t td_ctl0; 836 volatile uint32_t td_ctl1; 837 volatile uint32_t td_buf; 838 volatile uint32_t td_len; 839 volatile uint32_t td_next; 840 volatile uint32_t td_rsvd[3]; 841 } __packed __aligned(4); 842 843 #define td_stat td_ctl0 844 845 #define RTW_TXCTL0_OWN __BIT(31) /* 1: ready to Tx */ 846 #define RTW_TXCTL0_RSVD0 __BIT(30) /* reserved */ 847 #define RTW_TXCTL0_FS __BIT(29) /* first segment */ 848 #define RTW_TXCTL0_LS __BIT(28) /* last segment */ 849 850 #define RTW_TXCTL0_RATE_MASK __BITS(27,24) /* Tx rate */ 851 #define RTW_TXCTL0_RATE_1MBPS __SHIFTIN(0, RTW_TXCTL0_RATE_MASK) 852 #define RTW_TXCTL0_RATE_2MBPS __SHIFTIN(1, RTW_TXCTL0_RATE_MASK) 853 #define RTW_TXCTL0_RATE_5MBPS __SHIFTIN(2, RTW_TXCTL0_RATE_MASK) 854 #define RTW_TXCTL0_RATE_11MBPS __SHIFTIN(3, RTW_TXCTL0_RATE_MASK) 855 856 #define RTW_TXCTL0_RTSEN __BIT(23) /* RTS Enable */ 857 858 #define RTW_TXCTL0_RTSRATE_MASK __BITS(22,19) /* Tx rate */ 859 #define RTW_TXCTL0_RTSRATE_1MBPS __SHIFTIN(0, RTW_TXCTL0_RTSRATE_MASK) 860 #define RTW_TXCTL0_RTSRATE_2MBPS __SHIFTIN(1, RTW_TXCTL0_RTSRATE_MASK) 861 #define RTW_TXCTL0_RTSRATE_5MBPS __SHIFTIN(2, RTW_TXCTL0_RTSRATE_MASK) 862 #define RTW_TXCTL0_RTSRATE_11MBPS __SHIFTIN(3, RTW_TXCTL0_RTSRATE_MASK) 863 864 #define RTW_TXCTL0_BEACON __BIT(18) /* packet is a beacon */ 865 #define RTW_TXCTL0_MOREFRAG __BIT(17) /* another fragment 866 * follows 867 */ 868 /* add short PLCP preamble and header */ 869 #define RTW_TXCTL0_SPLCP __BIT(16) 870 #define RTW_TXCTL0_KEYID_MASK __BITS(15,14) /* default key id */ 871 #define RTW_TXCTL0_RSVD1_MASK __BITS(13,12) /* reserved */ 872 #define RTW_TXCTL0_TPKTSIZE_MASK __BITS(11,0) /* Tx packet size 873 * in bytes 874 */ 875 876 #define RTW_TXSTAT_OWN RTW_TXCTL0_OWN 877 #define RTW_TXSTAT_RSVD0 RTW_TXCTL0_RSVD0 878 #define RTW_TXSTAT_FS RTW_TXCTL0_FS 879 #define RTW_TXSTAT_LS RTW_TXCTL0_LS 880 #define RTW_TXSTAT_RSVD1_MASK __BITS(27,16) 881 #define RTW_TXSTAT_TOK __BIT(15) 882 #define RTW_TXSTAT_RTSRETRY_MASK __BITS(14,8) /* RTS retry count */ 883 #define RTW_TXSTAT_DRC_MASK __BITS(7,0) /* Data retry count */ 884 885 #define RTW_TXCTL1_LENGEXT __BIT(31) /* supplements _LENGTH 886 * in packets sent 5.5Mb/s or 887 * faster 888 */ 889 #define RTW_TXCTL1_LENGTH_MASK __BITS(30,16) /* PLCP length (microseconds) */ 890 #define RTW_TXCTL1_RTSDUR_MASK __BITS(15,0) /* RTS Duration 891 * (microseconds) 892 */ 893 894 #define RTW_TXLEN_LENGTH_MASK __BITS(11,0) /* Tx buffer length in bytes */ 895 896 /* Rx descriptor */ 897 struct rtw_rxdesc { 898 volatile uint32_t rd_ctl; 899 volatile uint32_t rd_rsvd0; 900 volatile uint32_t rd_buf; 901 volatile uint32_t rd_rsvd1; 902 } __packed __aligned(4); 903 904 #define rd_stat rd_ctl 905 #define rd_rssi rd_rsvd0 906 #define rd_tsftl rd_buf /* valid only when RTW_RXSTAT_LS is set */ 907 #define rd_tsfth rd_rsvd1 /* valid only when RTW_RXSTAT_LS is set */ 908 909 #define RTW_RXCTL_OWN __BIT(31) /* 1: owned by NIC */ 910 #define RTW_RXCTL_EOR __BIT(30) /* end of ring */ 911 #define RTW_RXCTL_FS __BIT(29) /* first segment */ 912 #define RTW_RXCTL_LS __BIT(28) /* last segment */ 913 #define RTW_RXCTL_RSVD0_MASK __BITS(29,12) /* reserved */ 914 #define RTW_RXCTL_LENGTH_MASK __BITS(11,0) /* Rx buffer length */ 915 916 #define RTW_RXSTAT_OWN RTW_RXCTL_OWN 917 #define RTW_RXSTAT_EOR RTW_RXCTL_EOR 918 #define RTW_RXSTAT_FS RTW_RXCTL_FS /* first segment */ 919 #define RTW_RXSTAT_LS RTW_RXCTL_LS /* last segment */ 920 #define RTW_RXSTAT_DMAFAIL __BIT(27) /* DMA failure on this pkt */ 921 #define RTW_RXSTAT_BOVF __BIT(26) /* buffer overflow XXX means 922 * FIFO exhausted? 923 */ 924 #define RTW_RXSTAT_SPLCP __BIT(25) /* Rx'd with short preamble 925 * and PLCP header 926 */ 927 #define RTW_RXSTAT_RSVD1 __BIT(24) /* reserved */ 928 #define RTW_RXSTAT_RATE_MASK __BITS(23,20) /* Rx rate */ 929 #define RTW_RXSTAT_RATE_1MBPS __SHIFTIN(0, RTW_RXSTAT_RATE_MASK) 930 #define RTW_RXSTAT_RATE_2MBPS __SHIFTIN(1, RTW_RXSTAT_RATE_MASK) 931 #define RTW_RXSTAT_RATE_5MBPS __SHIFTIN(2, RTW_RXSTAT_RATE_MASK) 932 #define RTW_RXSTAT_RATE_11MBPS __SHIFTIN(3, RTW_RXSTAT_RATE_MASK) 933 #define RTW_RXSTAT_MIC __BIT(19) /* XXX from reference driver */ 934 #define RTW_RXSTAT_MAR __BIT(18) /* is multicast */ 935 #define RTW_RXSTAT_PAR __BIT(17) /* matches RTL8180's MAC */ 936 #define RTW_RXSTAT_BAR __BIT(16) /* is broadcast */ 937 #define RTW_RXSTAT_RES __BIT(15) /* error summary. valid when 938 * RTW_RXSTAT_LS set. indicates 939 * that either RTW_RXSTAT_CRC32 940 * or RTW_RXSTAT_ICV is set. 941 */ 942 #define RTW_RXSTAT_PWRMGT __BIT(14) /* 802.11 PWRMGMT bit is set */ 943 #define RTW_RXSTAT_CRC16 __BIT(14) /* XXX CRC16 error, from 944 * reference driver 945 */ 946 #define RTW_RXSTAT_CRC32 __BIT(13) /* CRC32 error */ 947 #define RTW_RXSTAT_ICV __BIT(12) /* ICV error */ 948 #define RTW_RXSTAT_LENGTH_MASK __BITS(11,0) /* frame length, including 949 * CRC32 950 */ 951 952 /* Convenient status conjunction. */ 953 #define RTW_RXSTAT_ONESEG (RTW_RXSTAT_FS|RTW_RXSTAT_LS) 954 /* Convenient status disjunctions. */ 955 #define RTW_RXSTAT_IOERROR (RTW_RXSTAT_DMAFAIL|RTW_RXSTAT_BOVF) 956 #define RTW_RXSTAT_DEBUG (RTW_RXSTAT_SPLCP|RTW_RXSTAT_MAR|\ 957 RTW_RXSTAT_PAR|RTW_RXSTAT_BAR|\ 958 RTW_RXSTAT_PWRMGT|RTW_RXSTAT_CRC32|\ 959 RTW_RXSTAT_ICV) 960 961 962 #define RTW_RXRSSI_VLAN __BITS(31,16) /* XXX from reference driver */ 963 /* for Philips RF front-ends */ 964 #define RTW_RXRSSI_RSSI __BITS(15,8) /* RF energy at the PHY */ 965 /* for RF front-ends by Intersil, Maxim, RFMD */ 966 #define RTW_RXRSSI_IMR_RSSI __BITS(15,9) /* RF energy at the PHY */ 967 #define RTW_RXRSSI_IMR_LNA __BIT(8) /* 1: LNA activated */ 968 #define RTW_RXRSSI_SQ __BITS(7,0) /* Barker code-lock quality */ 969 970 #define RTW_READ8(regs, ofs) \ 971 bus_space_read_1((regs)->r_bt, (regs)->r_bh, (ofs)) 972 973 #define RTW_READ16(regs, ofs) \ 974 bus_space_read_2((regs)->r_bt, (regs)->r_bh, (ofs)) 975 976 #define RTW_READ(regs, ofs) \ 977 bus_space_read_4((regs)->r_bt, (regs)->r_bh, (ofs)) 978 979 #define RTW_WRITE8(regs, ofs, val) \ 980 bus_space_write_1((regs)->r_bt, (regs)->r_bh, (ofs), (val)) 981 982 #define RTW_WRITE16(regs, ofs, val) \ 983 bus_space_write_2((regs)->r_bt, (regs)->r_bh, (ofs), (val)) 984 985 #define RTW_WRITE(regs, ofs, val) \ 986 bus_space_write_4((regs)->r_bt, (regs)->r_bh, (ofs), (val)) 987 988 #define RTW_ISSET(regs, reg, mask) \ 989 (RTW_READ((regs), (reg)) & (mask)) 990 991 #define RTW_CLR(regs, reg, mask) \ 992 RTW_WRITE((regs), (reg), RTW_READ((regs), (reg)) & ~(mask)) 993 994 /* 995 * Registers for RTL8180L's built-in baseband modem. 996 */ 997 #define RTW_BBP_SYS1 0x00 998 #define RTW_BBP_TXAGC 0x03 /* guess: transmit auto gain control */ 999 #define RTW_BBP_LNADET 0x04 /* guess: low-noise amplifier activation 1000 * threshold 1001 */ 1002 #define RTW_BBP_IFAGCINI 0x05 /* guess: intermediate frequency (IF) 1003 * auto-gain control (AGC) initial value 1004 */ 1005 #define RTW_BBP_IFAGCLIMIT 0x06 /* guess: IF AGC maximum value */ 1006 #define RTW_BBP_IFAGCDET 0x07 /* guess: activation threshold for 1007 * IF AGC loop 1008 */ 1009 1010 #define RTW_BBP_ANTATTEN 0x10 /* guess: antenna & attenuation */ 1011 #define RTW_BBP_ANTATTEN_GCT_MAGIC 0xa3 1012 #define RTW_BBP_ANTATTEN_PHILIPS_MAGIC 0x91 1013 #define RTW_BBP_ANTATTEN_INTERSIL_MAGIC 0x92 1014 #define RTW_BBP_ANTATTEN_RFMD_MAGIC 0x93 1015 #define RTW_BBP_ANTATTEN_MAXIM_MAGIC 0xb3 1016 #define RTW_BBP_ANTATTEN_DFLANTB 0x40 1017 #define RTW_BBP_ANTATTEN_CHAN14 0x0c 1018 1019 #define RTW_BBP_TRL 0x11 /* guess: transmit/receive 1020 * switch latency 1021 */ 1022 #define RTW_BBP_SYS2 0x12 1023 #define RTW_BBP_SYS2_ANTDIV 0x80 /* enable antenna diversity */ 1024 #define RTW_BBP_SYS2_RATE_MASK __BITS(5,4) /* loopback rate? 1025 * 0: 1Mbps 1026 * 1: 2Mbps 1027 * 2: 5.5Mbps 1028 * 3: 11Mbps 1029 */ 1030 #define RTW_BBP_SYS3 0x13 1031 /* carrier-sense threshold */ 1032 #define RTW_BBP_SYS3_CSTHRESH_MASK __BITS(0,3) 1033 #define RTW_BBP_CHESTLIM 0x19 /* guess: channel energy-detect 1034 * threshold 1035 */ 1036 #define RTW_BBP_CHSQLIM 0x1a /* guess: channel signal-quality 1037 * threshold 1038 */ 1039