1 /*-
2 * Copyright (c) 2002-2009 Sam Leffler, Errno Consulting
3 * All rights reserved.
4 *
5 * Redistribution and use in source and binary forms, with or without
6 * modification, are permitted provided that the following conditions
7 * are met:
8 * 1. Redistributions of source code must retain the above copyright
9 * notice, this list of conditions and the following disclaimer,
10 * without modification.
11 * 2. Redistributions in binary form must reproduce at minimum a disclaimer
12 * similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
13 * redistribution must be conditioned upon including a substantially
14 * similar Disclaimer requirement for further binary redistribution.
15 *
16 * NO WARRANTY
17 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
18 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
19 * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
20 * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
21 * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
22 * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
23 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
24 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
25 * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
26 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
27 * THE POSSIBILITY OF SUCH DAMAGES.
28 */
29
30 #include <sys/cdefs.h>
31 __FBSDID("$FreeBSD$");
32
33 /*
34 * Driver for the Atheros Wireless LAN controller.
35 *
36 * This software is derived from work of Atsushi Onoe; his contribution
37 * is greatly appreciated.
38 */
39
40 #include "opt_inet.h"
41 #include "opt_ath.h"
42 /*
43 * This is needed for register operations which are performed
44 * by the driver - eg, calls to ath_hal_gettsf32().
45 *
46 * It's also required for any AH_DEBUG checks in here, eg the
47 * module dependencies.
48 */
49 #include "opt_ah.h"
50 #include "opt_wlan.h"
51
52 #include <sys/param.h>
53 #include <sys/systm.h>
54 #include <sys/sysctl.h>
55 #include <sys/mbuf.h>
56 #include <sys/malloc.h>
57 #include <sys/lock.h>
58 #include <sys/mutex.h>
59 #include <sys/kernel.h>
60 #include <sys/socket.h>
61 #include <sys/sockio.h>
62 #include <sys/errno.h>
63 #include <sys/callout.h>
64 #include <sys/bus.h>
65 #include <sys/endian.h>
66 #include <sys/kthread.h>
67 #include <sys/taskqueue.h>
68 #include <sys/priv.h>
69 #include <sys/module.h>
70 #include <sys/ktr.h>
71 #include <sys/smp.h> /* for mp_ncpus */
72
73 #include <machine/bus.h>
74
75 #include <net/if.h>
76 #include <net/if_dl.h>
77 #include <net/if_media.h>
78 #include <net/if_types.h>
79 #include <net/if_arp.h>
80 #include <net/ethernet.h>
81 #include <net/if_llc.h>
82
83 #include <net80211/ieee80211_var.h>
84 #include <net80211/ieee80211_regdomain.h>
85 #ifdef IEEE80211_SUPPORT_SUPERG
86 #include <net80211/ieee80211_superg.h>
87 #endif
88 #ifdef IEEE80211_SUPPORT_TDMA
89 #include <net80211/ieee80211_tdma.h>
90 #endif
91
92 #include <net/bpf.h>
93
94 #ifdef INET
95 #include <netinet/in.h>
96 #include <netinet/if_ether.h>
97 #endif
98
99 #include <dev/ath/if_athvar.h>
100 #include <dev/ath/ath_hal/ah_devid.h> /* XXX for softled */
101 #include <dev/ath/ath_hal/ah_diagcodes.h>
102
103 #include <dev/ath/if_ath_debug.h>
104 #include <dev/ath/if_ath_misc.h>
105 #include <dev/ath/if_ath_tsf.h>
106 #include <dev/ath/if_ath_tx.h>
107 #include <dev/ath/if_ath_sysctl.h>
108 #include <dev/ath/if_ath_led.h>
109 #include <dev/ath/if_ath_keycache.h>
110 #include <dev/ath/if_ath_rx.h>
111 #include <dev/ath/if_ath_beacon.h>
112 #include <dev/ath/if_athdfs.h>
113
114 #ifdef ATH_TX99_DIAG
115 #include <dev/ath/ath_tx99/ath_tx99.h>
116 #endif
117
118 #ifdef ATH_DEBUG_ALQ
119 #include <dev/ath/if_ath_alq.h>
120 #endif
121
122 #ifdef IEEE80211_SUPPORT_TDMA
123 #include <dev/ath/if_ath_tdma.h>
124
125 static void ath_tdma_settimers(struct ath_softc *sc, u_int32_t nexttbtt,
126 u_int32_t bintval);
127 static void ath_tdma_bintvalsetup(struct ath_softc *sc,
128 const struct ieee80211_tdma_state *tdma);
129 #endif /* IEEE80211_SUPPORT_TDMA */
130
131 #ifdef IEEE80211_SUPPORT_TDMA
132 static void
ath_tdma_settimers(struct ath_softc * sc,u_int32_t nexttbtt,u_int32_t bintval)133 ath_tdma_settimers(struct ath_softc *sc, u_int32_t nexttbtt, u_int32_t bintval)
134 {
135 struct ath_hal *ah = sc->sc_ah;
136 HAL_BEACON_TIMERS bt;
137
138 bt.bt_intval = bintval | HAL_BEACON_ENA;
139 bt.bt_nexttbtt = nexttbtt;
140 bt.bt_nextdba = (nexttbtt<<3) - sc->sc_tdmadbaprep;
141 bt.bt_nextswba = (nexttbtt<<3) - sc->sc_tdmaswbaprep;
142 bt.bt_nextatim = nexttbtt+1;
143 /* Enables TBTT, DBA, SWBA timers by default */
144 bt.bt_flags = 0;
145 #if 0
146 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER,
147 "%s: intval=%d (0x%08x) nexttbtt=%u (0x%08x), nextdba=%u (0x%08x), nextswba=%u (0x%08x),nextatim=%u (0x%08x)\n",
148 __func__,
149 bt.bt_intval,
150 bt.bt_intval,
151 bt.bt_nexttbtt,
152 bt.bt_nexttbtt,
153 bt.bt_nextdba,
154 bt.bt_nextdba,
155 bt.bt_nextswba,
156 bt.bt_nextswba,
157 bt.bt_nextatim,
158 bt.bt_nextatim);
159 #endif
160
161 #ifdef ATH_DEBUG_ALQ
162 if (if_ath_alq_checkdebug(&sc->sc_alq, ATH_ALQ_TDMA_TIMER_SET)) {
163 struct if_ath_alq_tdma_timer_set t;
164 t.bt_intval = htobe32(bt.bt_intval);
165 t.bt_nexttbtt = htobe32(bt.bt_nexttbtt);
166 t.bt_nextdba = htobe32(bt.bt_nextdba);
167 t.bt_nextswba = htobe32(bt.bt_nextswba);
168 t.bt_nextatim = htobe32(bt.bt_nextatim);
169 t.bt_flags = htobe32(bt.bt_flags);
170 t.sc_tdmadbaprep = htobe32(sc->sc_tdmadbaprep);
171 t.sc_tdmaswbaprep = htobe32(sc->sc_tdmaswbaprep);
172 if_ath_alq_post(&sc->sc_alq, ATH_ALQ_TDMA_TIMER_SET,
173 sizeof(t), (char *) &t);
174 }
175 #endif
176
177 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER,
178 "%s: nexttbtt=%u (0x%08x), nexttbtt tsf=%lld (0x%08llx)\n",
179 __func__,
180 bt.bt_nexttbtt,
181 bt.bt_nexttbtt,
182 (long long) ( ((u_int64_t) (bt.bt_nexttbtt)) << 10),
183 (long long) ( ((u_int64_t) (bt.bt_nexttbtt)) << 10));
184 ath_hal_beaconsettimers(ah, &bt);
185 }
186
187 /*
188 * Calculate the beacon interval. This is periodic in the
189 * superframe for the bss. We assume each station is configured
190 * identically wrt transmit rate so the guard time we calculate
191 * above will be the same on all stations. Note we need to
192 * factor in the xmit time because the hardware will schedule
193 * a frame for transmit if the start of the frame is within
194 * the burst time. When we get hardware that properly kills
195 * frames in the PCU we can reduce/eliminate the guard time.
196 *
197 * Roundup to 1024 is so we have 1 TU buffer in the guard time
198 * to deal with the granularity of the nexttbtt timer. 11n MAC's
199 * with 1us timer granularity should allow us to reduce/eliminate
200 * this.
201 */
202 static void
ath_tdma_bintvalsetup(struct ath_softc * sc,const struct ieee80211_tdma_state * tdma)203 ath_tdma_bintvalsetup(struct ath_softc *sc,
204 const struct ieee80211_tdma_state *tdma)
205 {
206 /* copy from vap state (XXX check all vaps have same value?) */
207 sc->sc_tdmaslotlen = tdma->tdma_slotlen;
208
209 sc->sc_tdmabintval = roundup((sc->sc_tdmaslotlen+sc->sc_tdmaguard) *
210 tdma->tdma_slotcnt, 1024);
211 sc->sc_tdmabintval >>= 10; /* TSF -> TU */
212 if (sc->sc_tdmabintval & 1)
213 sc->sc_tdmabintval++;
214
215 if (tdma->tdma_slot == 0) {
216 /*
217 * Only slot 0 beacons; other slots respond.
218 */
219 sc->sc_imask |= HAL_INT_SWBA;
220 sc->sc_tdmaswba = 0; /* beacon immediately */
221 } else {
222 /* XXX all vaps must be slot 0 or slot !0 */
223 sc->sc_imask &= ~HAL_INT_SWBA;
224 }
225 }
226
227 /*
228 * Max 802.11 overhead. This assumes no 4-address frames and
229 * the encapsulation done by ieee80211_encap (llc). We also
230 * include potential crypto overhead.
231 */
232 #define IEEE80211_MAXOVERHEAD \
233 (sizeof(struct ieee80211_qosframe) \
234 + sizeof(struct llc) \
235 + IEEE80211_ADDR_LEN \
236 + IEEE80211_WEP_IVLEN \
237 + IEEE80211_WEP_KIDLEN \
238 + IEEE80211_WEP_CRCLEN \
239 + IEEE80211_WEP_MICLEN \
240 + IEEE80211_CRC_LEN)
241
242 /*
243 * Setup initially for tdma operation. Start the beacon
244 * timers and enable SWBA if we are slot 0. Otherwise
245 * we wait for slot 0 to arrive so we can sync up before
246 * starting to transmit.
247 */
248 void
ath_tdma_config(struct ath_softc * sc,struct ieee80211vap * vap)249 ath_tdma_config(struct ath_softc *sc, struct ieee80211vap *vap)
250 {
251 struct ath_hal *ah = sc->sc_ah;
252 struct ifnet *ifp = sc->sc_ifp;
253 struct ieee80211com *ic = ifp->if_l2com;
254 const struct ieee80211_txparam *tp;
255 const struct ieee80211_tdma_state *tdma = NULL;
256 int rix;
257
258 if (vap == NULL) {
259 vap = TAILQ_FIRST(&ic->ic_vaps); /* XXX */
260 if (vap == NULL) {
261 if_printf(ifp, "%s: no vaps?\n", __func__);
262 return;
263 }
264 }
265 /* XXX should take a locked ref to iv_bss */
266 tp = vap->iv_bss->ni_txparms;
267 /*
268 * Calculate the guard time for each slot. This is the
269 * time to send a maximal-size frame according to the
270 * fixed/lowest transmit rate. Note that the interface
271 * mtu does not include the 802.11 overhead so we must
272 * tack that on (ath_hal_computetxtime includes the
273 * preamble and plcp in it's calculation).
274 */
275 tdma = vap->iv_tdma;
276 if (tp->ucastrate != IEEE80211_FIXED_RATE_NONE)
277 rix = ath_tx_findrix(sc, tp->ucastrate);
278 else
279 rix = ath_tx_findrix(sc, tp->mcastrate);
280
281 /*
282 * If the chip supports enforcing TxOP on transmission,
283 * we can just delete the guard window. It isn't at all required.
284 */
285 if (sc->sc_hasenforcetxop) {
286 sc->sc_tdmaguard = 0;
287 } else {
288 /* XXX short preamble assumed */
289 /* XXX non-11n rate assumed */
290 sc->sc_tdmaguard = ath_hal_computetxtime(ah, sc->sc_currates,
291 ifp->if_mtu + IEEE80211_MAXOVERHEAD, rix, AH_TRUE);
292 }
293
294 ath_hal_intrset(ah, 0);
295
296 ath_beaconq_config(sc); /* setup h/w beacon q */
297 if (sc->sc_setcca)
298 ath_hal_setcca(ah, AH_FALSE); /* disable CCA */
299 ath_tdma_bintvalsetup(sc, tdma); /* calculate beacon interval */
300 ath_tdma_settimers(sc, sc->sc_tdmabintval,
301 sc->sc_tdmabintval | HAL_BEACON_RESET_TSF);
302 sc->sc_syncbeacon = 0;
303
304 sc->sc_avgtsfdeltap = TDMA_DUMMY_MARKER;
305 sc->sc_avgtsfdeltam = TDMA_DUMMY_MARKER;
306
307 ath_hal_intrset(ah, sc->sc_imask);
308
309 DPRINTF(sc, ATH_DEBUG_TDMA, "%s: slot %u len %uus cnt %u "
310 "bsched %u guard %uus bintval %u TU dba prep %u\n", __func__,
311 tdma->tdma_slot, tdma->tdma_slotlen, tdma->tdma_slotcnt,
312 tdma->tdma_bintval, sc->sc_tdmaguard, sc->sc_tdmabintval,
313 sc->sc_tdmadbaprep);
314
315 #ifdef ATH_DEBUG_ALQ
316 if (if_ath_alq_checkdebug(&sc->sc_alq, ATH_ALQ_TDMA_TIMER_CONFIG)) {
317 struct if_ath_alq_tdma_timer_config t;
318
319 t.tdma_slot = htobe32(tdma->tdma_slot);
320 t.tdma_slotlen = htobe32(tdma->tdma_slotlen);
321 t.tdma_slotcnt = htobe32(tdma->tdma_slotcnt);
322 t.tdma_bintval = htobe32(tdma->tdma_bintval);
323 t.tdma_guard = htobe32(sc->sc_tdmaguard);
324 t.tdma_scbintval = htobe32(sc->sc_tdmabintval);
325 t.tdma_dbaprep = htobe32(sc->sc_tdmadbaprep);
326
327 if_ath_alq_post(&sc->sc_alq, ATH_ALQ_TDMA_TIMER_CONFIG,
328 sizeof(t), (char *) &t);
329 }
330 #endif /* ATH_DEBUG_ALQ */
331 }
332
333 /*
334 * Update tdma operation. Called from the 802.11 layer
335 * when a beacon is received from the TDMA station operating
336 * in the slot immediately preceding us in the bss. Use
337 * the rx timestamp for the beacon frame to update our
338 * beacon timers so we follow their schedule. Note that
339 * by using the rx timestamp we implicitly include the
340 * propagation delay in our schedule.
341 *
342 * XXX TODO: since the changes for the AR5416 and later chips
343 * involved changing the TSF/TU calculations, we need to make
344 * sure that various calculations wrap consistently.
345 *
346 * A lot of the problems stemmed from the calculations wrapping
347 * at 65,535 TU. Since a lot of the math is still being done in
348 * TU, please audit it to ensure that when the TU values programmed
349 * into the timers wrap at (2^31)-1 TSF, all the various terms
350 * wrap consistently.
351 */
352 void
ath_tdma_update(struct ieee80211_node * ni,const struct ieee80211_tdma_param * tdma,int changed)353 ath_tdma_update(struct ieee80211_node *ni,
354 const struct ieee80211_tdma_param *tdma, int changed)
355 {
356 #define TSF_TO_TU(_h,_l) \
357 ((((u_int32_t)(_h)) << 22) | (((u_int32_t)(_l)) >> 10))
358 #define TU_TO_TSF(_tu) (((u_int64_t)(_tu)) << 10)
359 struct ieee80211vap *vap = ni->ni_vap;
360 struct ieee80211com *ic = ni->ni_ic;
361 struct ath_softc *sc = ic->ic_ifp->if_softc;
362 struct ath_hal *ah = sc->sc_ah;
363 const HAL_RATE_TABLE *rt = sc->sc_currates;
364 u_int64_t tsf, rstamp, nextslot, nexttbtt, nexttbtt_full;
365 u_int32_t txtime, nextslottu;
366 int32_t tudelta, tsfdelta;
367 const struct ath_rx_status *rs;
368 int rix;
369
370 sc->sc_stats.ast_tdma_update++;
371
372 /*
373 * Check for and adopt configuration changes.
374 */
375 if (changed != 0) {
376 const struct ieee80211_tdma_state *ts = vap->iv_tdma;
377
378 ath_tdma_bintvalsetup(sc, ts);
379 if (changed & TDMA_UPDATE_SLOTLEN)
380 ath_wme_update(ic);
381
382 DPRINTF(sc, ATH_DEBUG_TDMA,
383 "%s: adopt slot %u slotcnt %u slotlen %u us "
384 "bintval %u TU\n", __func__,
385 ts->tdma_slot, ts->tdma_slotcnt, ts->tdma_slotlen,
386 sc->sc_tdmabintval);
387
388 /* XXX right? */
389 ath_hal_intrset(ah, sc->sc_imask);
390 /* NB: beacon timers programmed below */
391 }
392
393 /* extend rx timestamp to 64 bits */
394 rs = sc->sc_lastrs;
395 tsf = ath_hal_gettsf64(ah);
396 rstamp = ath_extend_tsf(sc, rs->rs_tstamp, tsf);
397 /*
398 * The rx timestamp is set by the hardware on completing
399 * reception (at the point where the rx descriptor is DMA'd
400 * to the host). To find the start of our next slot we
401 * must adjust this time by the time required to send
402 * the packet just received.
403 */
404 rix = rt->rateCodeToIndex[rs->rs_rate];
405
406 /*
407 * To calculate the packet duration for legacy rates, we
408 * only need the rix and preamble.
409 *
410 * For 11n non-aggregate frames, we also need the channel
411 * width and short/long guard interval.
412 *
413 * For 11n aggregate frames, the required hacks are a little
414 * more subtle. You need to figure out the frame duration
415 * for each frame, including the delimiters. However, when
416 * a frame isn't received successfully, we won't hear it
417 * (unless you enable reception of CRC errored frames), so
418 * your duration calculation is going to be off.
419 *
420 * However, we can assume that the beacon frames won't be
421 * transmitted as aggregate frames, so we should be okay.
422 * Just add a check to ensure that we aren't handed something
423 * bad.
424 *
425 * For ath_hal_pkt_txtime() - for 11n rates, shortPreamble is
426 * actually short guard interval. For legacy rates,
427 * it's short preamble.
428 */
429 txtime = ath_hal_pkt_txtime(ah, rt, rs->rs_datalen,
430 rix,
431 !! (rs->rs_flags & HAL_RX_2040),
432 (rix & 0x80) ?
433 (! (rs->rs_flags & HAL_RX_GI)) : rt->info[rix].shortPreamble);
434 /* NB: << 9 is to cvt to TU and /2 */
435 nextslot = (rstamp - txtime) + (sc->sc_tdmabintval << 9);
436
437 /*
438 * For 802.11n chips: nextslottu needs to be the full TSF space,
439 * not just 0..65535 TU.
440 */
441 nextslottu = TSF_TO_TU(nextslot>>32, nextslot);
442 /*
443 * Retrieve the hardware NextTBTT in usecs
444 * and calculate the difference between what the
445 * other station thinks and what we have programmed. This
446 * lets us figure how to adjust our timers to match. The
447 * adjustments are done by pulling the TSF forward and possibly
448 * rewriting the beacon timers.
449 */
450 /*
451 * The logic here assumes the nexttbtt counter is in TSF
452 * but the prr-11n NICs are in TU. The HAL shifts them
453 * to TSF but there's two important differences:
454 *
455 * + The TU->TSF values have 0's for the low 9 bits, and
456 * + The counter wraps at TU_TO_TSF(HAL_BEACON_PERIOD + 1) for
457 * the pre-11n NICs, but not for the 11n NICs.
458 *
459 * So for now, just make sure the nexttbtt value we get
460 * matches the second issue or once nexttbtt exceeds this
461 * value, tsfdelta ends up becoming very negative and all
462 * of the adjustments get very messed up.
463 */
464
465 /*
466 * We need to track the full nexttbtt rather than having it
467 * truncated at HAL_BEACON_PERIOD, as programming the
468 * nexttbtt (and related) registers for the 11n chips is
469 * actually going to take the full 32 bit space, rather than
470 * just 0..65535 TU.
471 */
472 nexttbtt_full = ath_hal_getnexttbtt(ah);
473 nexttbtt = nexttbtt_full % (TU_TO_TSF(HAL_BEACON_PERIOD + 1));
474 tsfdelta = (int32_t)((nextslot % TU_TO_TSF(HAL_BEACON_PERIOD + 1)) - nexttbtt);
475
476 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER,
477 "rs->rstamp %llu rstamp %llu tsf %llu txtime %d, nextslot %llu, "
478 "nextslottu %d, nextslottume %d\n",
479 (unsigned long long) rs->rs_tstamp, rstamp, tsf, txtime,
480 nextslot, nextslottu, TSF_TO_TU(nextslot >> 32, nextslot));
481 DPRINTF(sc, ATH_DEBUG_TDMA,
482 " beacon tstamp: %llu (0x%016llx)\n",
483 le64toh(ni->ni_tstamp.tsf),
484 le64toh(ni->ni_tstamp.tsf));
485
486 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER,
487 "nexttbtt %llu (0x%08llx) tsfdelta %d avg +%d/-%d\n",
488 nexttbtt,
489 (long long) nexttbtt,
490 tsfdelta,
491 TDMA_AVG(sc->sc_avgtsfdeltap), TDMA_AVG(sc->sc_avgtsfdeltam));
492
493 if (tsfdelta < 0) {
494 TDMA_SAMPLE(sc->sc_avgtsfdeltap, 0);
495 TDMA_SAMPLE(sc->sc_avgtsfdeltam, -tsfdelta);
496 tsfdelta = -tsfdelta % 1024;
497 nextslottu++;
498 } else if (tsfdelta > 0) {
499 TDMA_SAMPLE(sc->sc_avgtsfdeltap, tsfdelta);
500 TDMA_SAMPLE(sc->sc_avgtsfdeltam, 0);
501 tsfdelta = 1024 - (tsfdelta % 1024);
502 nextslottu++;
503 } else {
504 TDMA_SAMPLE(sc->sc_avgtsfdeltap, 0);
505 TDMA_SAMPLE(sc->sc_avgtsfdeltam, 0);
506 }
507 tudelta = nextslottu - TSF_TO_TU(nexttbtt_full >> 32, nexttbtt_full);
508
509 #ifdef ATH_DEBUG_ALQ
510 if (if_ath_alq_checkdebug(&sc->sc_alq, ATH_ALQ_TDMA_BEACON_STATE)) {
511 struct if_ath_alq_tdma_beacon_state t;
512 t.rx_tsf = htobe64(rstamp);
513 t.beacon_tsf = htobe64(le64toh(ni->ni_tstamp.tsf));
514 t.tsf64 = htobe64(tsf);
515 t.nextslot_tsf = htobe64(nextslot);
516 t.nextslot_tu = htobe32(nextslottu);
517 t.txtime = htobe32(txtime);
518 if_ath_alq_post(&sc->sc_alq, ATH_ALQ_TDMA_BEACON_STATE,
519 sizeof(t), (char *) &t);
520 }
521
522 if (if_ath_alq_checkdebug(&sc->sc_alq, ATH_ALQ_TDMA_SLOT_CALC)) {
523 struct if_ath_alq_tdma_slot_calc t;
524
525 t.nexttbtt = htobe64(nexttbtt_full);
526 t.next_slot = htobe64(nextslot);
527 t.tsfdelta = htobe32(tsfdelta);
528 t.avg_plus = htobe32(TDMA_AVG(sc->sc_avgtsfdeltap));
529 t.avg_minus = htobe32(TDMA_AVG(sc->sc_avgtsfdeltam));
530
531 if_ath_alq_post(&sc->sc_alq, ATH_ALQ_TDMA_SLOT_CALC,
532 sizeof(t), (char *) &t);
533 }
534 #endif
535
536 /*
537 * Copy sender's timetstamp into tdma ie so they can
538 * calculate roundtrip time. We submit a beacon frame
539 * below after any timer adjustment. The frame goes out
540 * at the next TBTT so the sender can calculate the
541 * roundtrip by inspecting the tdma ie in our beacon frame.
542 *
543 * NB: This tstamp is subtlely preserved when
544 * IEEE80211_BEACON_TDMA is marked (e.g. when the
545 * slot position changes) because ieee80211_add_tdma
546 * skips over the data.
547 */
548 memcpy(ATH_VAP(vap)->av_boff.bo_tdma +
549 __offsetof(struct ieee80211_tdma_param, tdma_tstamp),
550 &ni->ni_tstamp.data, 8);
551 #if 0
552 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER,
553 "tsf %llu nextslot %llu (%d, %d) nextslottu %u nexttbtt %llu (%d)\n",
554 (unsigned long long) tsf, (unsigned long long) nextslot,
555 (int)(nextslot - tsf), tsfdelta, nextslottu, nexttbtt, tudelta);
556 #endif
557 /*
558 * Adjust the beacon timers only when pulling them forward
559 * or when going back by less than the beacon interval.
560 * Negative jumps larger than the beacon interval seem to
561 * cause the timers to stop and generally cause instability.
562 * This basically filters out jumps due to missed beacons.
563 */
564 if (tudelta != 0 && (tudelta > 0 || -tudelta < sc->sc_tdmabintval)) {
565 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER,
566 "%s: calling ath_tdma_settimers; nextslottu=%d, bintval=%d\n",
567 __func__,
568 nextslottu,
569 sc->sc_tdmabintval);
570 ath_tdma_settimers(sc, nextslottu, sc->sc_tdmabintval);
571 sc->sc_stats.ast_tdma_timers++;
572 }
573 if (tsfdelta > 0) {
574 uint64_t tsf;
575
576 /* XXX should just teach ath_hal_adjusttsf() to do this */
577 tsf = ath_hal_gettsf64(ah);
578 ath_hal_settsf64(ah, tsf + tsfdelta);
579 DPRINTF(sc, ATH_DEBUG_TDMA_TIMER,
580 "%s: calling ath_hal_adjusttsf: TSF=%llu, tsfdelta=%d\n",
581 __func__,
582 tsf,
583 tsfdelta);
584
585 #ifdef ATH_DEBUG_ALQ
586 if (if_ath_alq_checkdebug(&sc->sc_alq,
587 ATH_ALQ_TDMA_TSF_ADJUST)) {
588 struct if_ath_alq_tdma_tsf_adjust t;
589
590 t.tsfdelta = htobe32(tsfdelta);
591 t.tsf64_old = htobe64(tsf);
592 t.tsf64_new = htobe64(tsf + tsfdelta);
593 if_ath_alq_post(&sc->sc_alq, ATH_ALQ_TDMA_TSF_ADJUST,
594 sizeof(t), (char *) &t);
595 }
596 #endif /* ATH_DEBUG_ALQ */
597 sc->sc_stats.ast_tdma_tsf++;
598 }
599 ath_tdma_beacon_send(sc, vap); /* prepare response */
600 #undef TU_TO_TSF
601 #undef TSF_TO_TU
602 }
603
604 /*
605 * Transmit a beacon frame at SWBA. Dynamic updates
606 * to the frame contents are done as needed.
607 */
608 void
ath_tdma_beacon_send(struct ath_softc * sc,struct ieee80211vap * vap)609 ath_tdma_beacon_send(struct ath_softc *sc, struct ieee80211vap *vap)
610 {
611 struct ath_hal *ah = sc->sc_ah;
612 struct ath_buf *bf;
613 int otherant;
614
615 /*
616 * Check if the previous beacon has gone out. If
617 * not don't try to post another, skip this period
618 * and wait for the next. Missed beacons indicate
619 * a problem and should not occur. If we miss too
620 * many consecutive beacons reset the device.
621 */
622 if (ath_hal_numtxpending(ah, sc->sc_bhalq) != 0) {
623 sc->sc_bmisscount++;
624 DPRINTF(sc, ATH_DEBUG_BEACON,
625 "%s: missed %u consecutive beacons\n",
626 __func__, sc->sc_bmisscount);
627 if (sc->sc_bmisscount >= ath_bstuck_threshold)
628 taskqueue_enqueue(sc->sc_tq, &sc->sc_bstucktask);
629 return;
630 }
631 if (sc->sc_bmisscount != 0) {
632 DPRINTF(sc, ATH_DEBUG_BEACON,
633 "%s: resume beacon xmit after %u misses\n",
634 __func__, sc->sc_bmisscount);
635 sc->sc_bmisscount = 0;
636 }
637
638 /*
639 * Check recent per-antenna transmit statistics and flip
640 * the default antenna if noticeably more frames went out
641 * on the non-default antenna.
642 * XXX assumes 2 anntenae
643 */
644 if (!sc->sc_diversity) {
645 otherant = sc->sc_defant & 1 ? 2 : 1;
646 if (sc->sc_ant_tx[otherant] > sc->sc_ant_tx[sc->sc_defant] + 2)
647 ath_setdefantenna(sc, otherant);
648 sc->sc_ant_tx[1] = sc->sc_ant_tx[2] = 0;
649 }
650
651 bf = ath_beacon_generate(sc, vap);
652 /* XXX We don't do cabq traffic, but just for completeness .. */
653 ATH_TXQ_LOCK(sc->sc_cabq);
654 ath_beacon_cabq_start(sc);
655 ATH_TXQ_UNLOCK(sc->sc_cabq);
656
657 if (bf != NULL) {
658 /*
659 * Stop any current dma and put the new frame on the queue.
660 * This should never fail since we check above that no frames
661 * are still pending on the queue.
662 */
663 if ((! sc->sc_isedma) &&
664 (! ath_hal_stoptxdma(ah, sc->sc_bhalq))) {
665 DPRINTF(sc, ATH_DEBUG_ANY,
666 "%s: beacon queue %u did not stop?\n",
667 __func__, sc->sc_bhalq);
668 /* NB: the HAL still stops DMA, so proceed */
669 }
670 ath_hal_puttxbuf(ah, sc->sc_bhalq, bf->bf_daddr);
671 ath_hal_txstart(ah, sc->sc_bhalq);
672
673 sc->sc_stats.ast_be_xmit++; /* XXX per-vap? */
674
675 /*
676 * Record local TSF for our last send for use
677 * in arbitrating slot collisions.
678 */
679 /* XXX should take a locked ref to iv_bss */
680 vap->iv_bss->ni_tstamp.tsf = ath_hal_gettsf64(ah);
681 }
682 }
683 #endif /* IEEE80211_SUPPORT_TDMA */
684