723 	DEBUGOUT("Soft resetting SGMII attached PHY...\n");  in e1000_phy_hw_reset_sgmii_82575()
955 			DEBUGOUT("Nvm bit banging access error detected and cleared.\n");  in e1000_acquire_nvm_82575()
965 			DEBUGOUT("Nvm bit banging access error detected and cleared.\n");  in e1000_acquire_nvm_82575()
1023 		DEBUGOUT("MNG configuration cycle has not completed.\n");  in e1000_get_cfg_done_82575()
1092 			DEBUGOUT("Error configuring flow control\n");  in e1000_check_for_link_82575()
1243 				DEBUGOUT("2500 Mbs, ");  in e1000_get_pcs_speed_and_duplex_82575()
1244 				DEBUGOUT("Full Duplex\n");  in e1000_get_pcs_speed_and_duplex_82575()
1312 		DEBUGOUT("PCI-E Master disable polling has failed.\n");  in e1000_reset_hw_82575()
1317 		DEBUGOUT("PCI-E Set completion timeout has failed.\n");  in e1000_reset_hw_82575()
1319 	DEBUGOUT("Masking off all interrupts\n");  in e1000_reset_hw_82575()
1330 	DEBUGOUT("Issuing a global reset to MAC\n");  in e1000_reset_hw_82575()
1340 		DEBUGOUT("Auto Read Done did not complete\n");  in e1000_reset_hw_82575()
1373 		DEBUGOUT("Error initializing identification LED\n");  in e1000_init_hw_82575()
1378 	DEBUGOUT("Initializing the IEEE VLAN\n");  in e1000_init_hw_82575()
1440 			DEBUGOUT("Error resetting the PHY.\n");  in e1000_setup_copper_link_82575()
1549 				DEBUGOUT("NVM Read Error\n");  in e1000_setup_serdes_link_82575()
1766 			DEBUGOUT("PHY module has not been recognized\n");  in e1000_set_sfp_media_type_82575()
1795 		DEBUGOUT("NVM Read Error\n");  in e1000_valid_led_default_82575()
1840 		DEBUGOUT("Running reset init script for 82575\n");  in e1000_reset_init_script_82575()
2202 		DEBUGOUT("NVM Read Error\n");  in e1000_reset_mdicnfg_82580()
2248 		DEBUGOUT("PCI-E Master disable polling has failed.\n");  in e1000_reset_hw_82580()
2250 	DEBUGOUT("Masking off all interrupts\n");  in e1000_reset_hw_82580()
2289 		DEBUGOUT("Auto Read Done did not complete\n");  in e1000_reset_hw_82580()
2301 		DEBUGOUT("Could not reset MDICNFG based on EEPROM\n");  in e1000_reset_hw_82580()
2353 			DEBUGOUT("NVM Read Error\n");  in e1000_validate_nvm_checksum_with_offset()
2360 		DEBUGOUT("NVM Checksum Invalid\n");  in e1000_validate_nvm_checksum_with_offset()
2390 			DEBUGOUT("NVM Read Error while updating checksum.\n");  in e1000_update_nvm_checksum_with_offset()
2399 		DEBUGOUT("NVM Write Error while updating checksum.\n");  in e1000_update_nvm_checksum_with_offset()
2424 		DEBUGOUT("NVM Read Error\n");  in e1000_validate_nvm_checksum_82580()
2464 		DEBUGOUT("NVM Read Error while updating checksum compatibility bit.\n");  in e1000_update_nvm_checksum_82580()
2474 			DEBUGOUT("NVM Write Error while updating checksum compatibility bit.\n");  in e1000_update_nvm_checksum_82580()
2664 		DEBUGOUT("Error committing the PHY changes\n");  in e1000_initialize_M88E1512_phy()
2763 		DEBUGOUT("Error committing the PHY changes\n");  in e1000_initialize_M88E1543_phy()
2812 			DEBUGOUT("LPI Clock Stop Bit should not be set!\n");  in e1000_set_eee_i350()
3099 			DEBUGOUT("I2C byte read error - Retrying.\n");  in e1000_read_i2c_byte_generic()
3101 			DEBUGOUT("I2C byte read error.\n");  in e1000_read_i2c_byte_generic()
3173 			DEBUGOUT("I2C byte write error - Retrying.\n");  in e1000_write_i2c_byte_generic()
3175 			DEBUGOUT("I2C byte write error.\n");  in e1000_write_i2c_byte_generic()
3329 		DEBUGOUT("I2C ack was not received.\n");  in e1000_get_i2c_ack()